WitBot Open Source Tango V1.0 Upgrade Rumba 3D Printer Motherboard with TMC2130/A4988/DRV8825 Driver for 12864 LCD for Reprap Mendel
Free Shipping Included! WitBot Open Source Tango V1.0 Upgrade Rumba 3D Printer Motherboard with TMC2130/A4988/DRV8825 Driver for 12864 LCD for Reprap Mendel by WitBot at TPC International. MPN: 6543724309. Hurry! Limited time offer. Offer valid only while supplies last. Driver installation Method:1. When installing the driver, you have to find the GND and DIR on the driver.2. Find the corresponding GND and DIR on the
Product Description & Reviews
Driver installation Method:
1. When installing the driver, you have to find the GND and DIR on the driver.
2. Find the corresponding GND and DIR on the motherboard and plug in the driver.
3.Then use a multimeter to adjust the voltage.
4.Stick the heat sink of the driver.
1. It is necessary to distinguish the positive and negative electrodes When connecting the power supply.
2. Please pay attention to the type of driver you have purchased and install it correctly.
3. This 3D printer motherboard has a large current, high temperature characteristics, must pay attention to fire prevention, protection! Do not place this motherboard next to flammable objects.
4. The temperature of the circuit board will rise sharply when the hot bed is heated. If the printer is in a bad position of air circulation, the circuit board fuse will be automatically disconnected because of the high temperature, and the hot bed cannot be heated.
5. If you use mechanical switches as limited switches, just need to connect "signal S" and "ground-wire" terminals, and the "power supply +" terminal does not need to be connected.If it wrongly connect the mechanical stop switch to the circuit board. The power +" and "ground -" terminals will burn the board.
6. If you plug in TMC2100 driver, please don't need to insert short-circuit cap under the driver.(if you choose TMC2130, it will be very quiet. )
Features & Highlights
- The Tango V1.0 baord is R&D for 3D Printer,which is Based on AVR Processor ATMEGA2560 controller board.It support three different color filament, and you can use a personal computer with a USB cable to control the 3D printer.
- Compared with other 3D printer control board(such as RAMPS, etc.), the Tango V1.0 support more motor drivers, Reduce some straight plug-in part, which improve the connectivity and stability.
- There are six stepper motor and five temperature sensor input interfaces;LCD expansion interface,support LCD screen and SD expansion interface, it can achieve offline printing.
- Using ATMEGA2560 as the main control chip, with high-performance USB to UART chip CP2102,it is compatible to all related RAMPS firmware.
- Power input is 12-24V, the rated voltage of the hot bed is same as the input voltage of the power supply, the voltage of the hot bed will be 12v if the voltage of power supply is 12v,and the voltage of the hot bed will be 24v if the voltage of power supply is 24v.
Printer Control Cards
6.38 x 1.81 x 10.55 inches
Have questions about this item, or would like to inquire about a custom or bulk order?
If you have any questions about this product by WitBot, contact us by completing and submitting the form below. If you are looking for a specif part number, please include it with your message.
Related Best Sellers
mpn: GMX-E750BAEAD22A643B9F210590F8A6FC9C, ean: 0670062875627,
Model Number:JZ-TS35 3.5 touchscreenItem Type:Display Screensize:3.5inchresolution :320*240 pxcompatible board :Mega2560 ramps1.4compatible firmware :Marlin/Repetier/Smoothiewarelanguage :English/Chinesecolor :262Kbaud rate:250000, 115200Power off: a...
mpn: YTN-D847B708E0BC0ADE6937152436D55512, ean: 0745832895645,
Item specifics:Model number: 620nType: OtherProduct name: server networkP/n: J7934A J7964GQuality: 95% new original ,usedWarranty: 3 monthsMin order: 1pcsUse for: 3005/4250/P3015/5200/8150/9000/500/800Package: neutral packingModel number: 620n. Type:...
sku: Q784460002-6283804, mpn: Q7844-60002, ean: 0609224635809,
Formatter Board - LJ 3050 AIO only...
mpn: GMX-D41D8CD98F00B204E9800998ECF8427E, ean: 0670062758692,
Descriptions: 100% brand new and high quality! After the power is off: the printing is completed, the nozzle is cooled, and the power is automatically turned off (expansion module). Speed optimization: high speed printing, or printing complex slice m...